Interfacing ILI9341 2.8" TFT TFT / Color with Raspberry Pi

ILI9341 2.8" TFT practical reference

The ILI9341 2.8-inch TFT display is a versatile color screen that brings vibrant visuals and touch interactivity to your projects. With a 320×240 resolution and support for 65K colors, it delivers crisp, bright images suitable for GUIs, dashboards, and multimedia applications.

The display is built around the ILI9341 driver chip, which includes a built-in video RAM buffer and supports SPI communication. A resistive touchscreen, controlled by an XPT2046 controller, enables intuitive user interaction. Many modules also feature a microSD card slot for storing images and assets.

Available in both SPI and 8-bit parallel interface variants, the SPI version is the most common and requires only a few I/O pins to operate. The module operates at 3.3V–5V, making it compatible with a wide range of microcontrollers. Onboard level-shifting circuitry ensures safe operation with both 3.3V and 5V logic.

Note: This entry covers the SPI version of the display, which is the most widely available and easiest to interface with. Parallel versions exist but are less common and require more I/O pins.

Key specifications

• Resolution: 320 × 240 pixels (QVGA)
• Color depth: 65K colors (RGB 16-bit 565)
• Display type: TFT, transmissive
• Touchscreen: Resistive (XPT2046 controller)
• Interface: SPI (4-wire) or 8-bit parallel
• Operating voltage: 3.3V – 5V (with onboard level shifter)
• Logic voltage: 3.3V
• Backlight: 4 white LEDs
• Active area: 43.2 × 57.6 mm
• Module dimensions: ~50 × 86 mm
• Operating temperature: -20°C to 60°C
• Storage temperature: -30°C to 70°C
• Extra features: microSD card slot

Pinout and connection notes

Critical usage notes:

• SPI vs Parallel: Most modules are SPI versions. Verify your module's interface before wiring — SPI uses fewer pins and is recommended for most projects.
• Level shifting: While many modules include onboard level shifters and accept 5V power, the logic pins are 3.3V. On 5V boards like the Uno, the onboard level shifter handles this — but check your specific module.
• Backlight: The LED pin controls the backlight. Connect to a PWM-capable pin for brightness control, or tie to VCC for always-on.
• Touch controller: The resistive touch uses an XPT2046 controller over SPI. Touch pins share the same SPI bus as the display but use a separate CS pin.
• Library support: The Adafruit_ILI9341 and TFT_eSPI libraries are the most widely used and well-documented options.
• SD card: If your module has an SD slot, it uses a separate SPI CS pin — typically Pin 4 on Arduino — and shares MOSI/MISO/SCK with the display.
• VCC: Power — 3.3V to 5V (onboard regulator/level shifter)
• GND: Ground
• CS: SPI chip select (active low)
• RESET: Reset, active low
• DC/RS: Data/Command select — high for data, low for command
• SDI/MOSI: SPI data in (Master Out Slave In)
• SCK: SPI clock
• LED: Backlight control — high to enable, or connect to 3.3V
• SDO/MISO: SPI data out (optional, for reading)
• T_CS: Touch SPI chip select (XPT2046)
• T_CLK: Touch SPI clock
• T_DIN: Touch SPI data in
• T_DO: Touch SPI data out
• T_IRQ: Touch interrupt — goes low when touch detected

Integration checklist

1. Confirm the exact part number and breakout-board revision.
2. Verify supply voltage, current demand, logic levels, and signal direction against the datasheet.
3. Check controller pin assignments and bus address or interface mode against the example code.
4. Power up with external loads disconnected, then test signals before full integration.
5. If readings or communication fail, check power and ground first, then pin mapping, interface settings, and library initialization.

Troubleshooting and reproducibility

Record the board used, wiring, library/version, supply arrangement, and measured behavior. Use the selected board-specific wiring example as the source of truth. Never assume visually similar modules share identical voltage tolerance or pin order.